Submissions from 1995
Finite element stress analysis of the wrist joint without and with an endoprosthesis., G. Lewis and S. R. Vannappagari
On the flow characteristics of various jets over a flat plate submerged in a uniform stream, F. R. Redding, J. D. Mo, and J. I. Hochstein
Accurate solution algorithms for incompressible multiphase flows, William J. Rider, Douglas B. Kothe, S. Jay Mosso, John H. Cerutti, and John I. Hochstein
Cyclic deformation and fatigue behaviour of ion-nitrided steel, J. Wan and A. Fatemi
Deformation and fatigue behavior of vanadium-based microalloyed forging steel in the as-forged and Q&T conditions, L. Yang and A. Fatemi
Submissions from 1994
On-orbit propellant motion resulting from an impulsive acceleration, John I. Hochstein, John C. Aydelot, Raymond C. Mjolsness, and Martin D. Torrey
Fatigue behavior of a 22Cr-20Ni-18Co-Fe alloy at elevated temperatures, T. H. Krukemyer, A. Fatemi, and R. W. Swindeman
The ankle joint prosthetic replacement: Clinical performance and research challenges, G. Lewis
A parametric finite element analysis study of the stresses in an endosseous implant, Gladius Lewis
Effect of methylene blue on the fracture toughness of acrylic bone cement, Gladius Lewis
Use of enzyme-linked immunosorbent assay (ELISA) for detection and quantification of monoclonal antibodies, Gladius Lewis
Mechanical properties of vacuum-mixed acrylic bone cement, Gladius Lewis and G. Ed Austin
Optimization of clubhead loft and swing elevation angles for maximum distance of a golf drive, D. C. Winfield and T. E. Tan
Submissions from 1993
Prediction of the transient thermodynamic response of a closed-cycle regenerative gas turbine, T. Korakianitis, J. I. Hochstein, and D. Zou
Stress analysis of a flexible one-piece type first metatarsophalangeal joint implant., G. Lewis and P. Alva
Electrochemical behavior of Ti-6Al-4V alloy in static biosimulating solutions., G. Lewis and K. Daigle
Predictors of clinical wear of restorative dental composite materials, Gladius Lewis
X-ray photoelectron spectroscopy study of surface layers on orthopaedic alloys. II. Co-Cr-Mo (ASTM F-75) alloy, Gladius Lewis
X-ray photoelectron study of surface layers on orthopaedic alloys. I. Ti-6AI-4V (ASTM F-136) alloy, Gladius Lewis
Marangoni convection with a curved and deforming free surface in a cavity, G. P. Sasmal and J. I. Hochstein
A study of optimal equivalent characteristics of insole materials, Yeu Sheng Shiue and Teong E. Tan
Study of optimal equivalent characteristics of insole materials, Yeu Sheng Shiue and Teong E. Tan
An experimental investigation of compressive behavior of a gasket material, Harry Willis and Ali Fatemi
Submissions from 1992
Pulsed thrust propellant reorientation - Concept and modeling, John I. Hochstein, Alfredo E. Patag, T. P. Korakianitis, and David J. Chato
Experimental verification of scaling parameters for thermal stratification, H. C. Ji, S. H. Schwartz, T. N. Lovrich, J. I. Hochstein, and L. A. Holmest
An empirical relation for estimating global irradiation for Tennessee, U.S.A., Gladius Lewis
Effect of lithotriptor treatment on the fracture toughness of acrylic bone cement, Gladius Lewis
Constitutive Equations for the Creep of a Silicon Carbide Whisker‐Reinforced Polycrystalline Alumina Composite Material, Gladius Lewis and Arnfinn Ostvoll
Small crack growth in multiaxial fatigue, Satish C. Reddy and Ali Fatemi
Submissions from 1991
Modeling of impulsive propellant reorientation, John I. Hochstein, T. P. Korakianitis, Alfredo E. Patag, and David J. Chato
In vivo occlusal wear of posterior composite restorations., G. Lewis
An assessment of the wind-energy utilization potential in tennessee, USA, Gladius Lewis
Thermal-creep strain of a nuclear fusion reactor first-wall ferrous material modified 9Cr-1Mo steel, Gladius Lewis
Constitutive thermal creep deformation relations for lifetime prediction of a fusion reactor first wall ferritic alloy, Gladius Lewis and Chung-Cheng Chuang
Characterization of the performance of shoe insert materials., G. Lewis, T. Tan, and Y. S. Shiue
Effects of mean stress on fatigue behaviour of a hardened carbon steel, T. Wehner and A. Fatemi
Submissions from 1990
Prediction of self-pressurization rate of cryogenic propellant tankage, John I. Hochstein, Hyun Chul Ji, and John C. Aydelott
Cracking mechanisms for mean stress/strain low-cycle multiaxial fatigue loadings, Peter Kurath and Ali Fatemi
Analyzing thermal creep strain of a tokamak first-wall steel, G. Lewis and C. C. Chuang
Using sizphot to solve engineering problems. Sizing of stand-alone photovoltaic power systems, Gladius Lewis
Submissions from 1989
Correlations for the erosive wear of materials by liquid slurries, G. Lewis
The utility of the Angstrom-type equation for the estimation of global irradiation, G. Lewis
Putting insoles through the paces, Gladius Lewis
Submissions from 1988
Multiaxial fatigue life predictions under the influence of mean-stresses, Ali Fatemi and Peter Kurath
A CRITICAL PLANE APPROACH TO MULTIAXIAL FATIGUE DAMAGE INCLUDING OUT‐OF‐PHASE LOADING, Ali Fatemi and Darrell F. Socie
Submissions from 1987
Numerical modeling of on-orbit propellant motion resulting from an impulsive acceleration, John C. Aydelott, Raymond C. Mjolsness, Martin D. Torrey, and John I. Hochstein
NUMERICAL MODELLING OF CRYOGENIC PROPELLANT BEHAVIOR IN LOW-G., John I. Hochstein
Temperature fields due to jet induced mixing in a typical OTV Tank, John I. Hochstein, Hyun Chul Ji, and John C. Aydelott
FILAMENT-WOUND SPHERICAL PRESSURE VESSELS: A STATE-OF-THE-ART REVIEW., Gladius Lewis
Optimal sizing of a collector for a solar domestic water heating system, Gladius Lewis
Optimum tilt of a solar collector, Gladius Lewis
The applicability of diffuse solar radiation models to Huntsville, Alabama, Gladius Lewis
Submissions from 1986
EFFECT OF SUBCOOLING ON THE ON-ORBIT PRESSURIZATION RATE OF CRYOGENIC PROPELLANT TANKAGE., J. I. Hochstein, H. C. Ji, and J. C. Aydelott
ANALYZING WEAR IN RP; ROUTE TO PERFORMANCE., Gladius Lewis
FRACTURE TOUGHNESS OF SOME TIMBERS., Gladius Lewis
SOME CORRELATES OF THE TRIBOLOGICAL PERFORMANCE OF COMPOSITE MATERIALS., Gladius Lewis
THEORIES OF FAILURE OF FILAMENT WOUND CASE COMPOSITE MATERIALS., Gladius Lewis
Wind power availability in Zimbabwe, Gladius Lewis
A full-suspension three-wheeled atv system: Part ii-roll, pitch and vertical motions, Teong Eng Tan and Jeffrey C. Huston
A full-suspension three-wheeled atv system: Part i-modeling and parameter values, Teong Eng Tan and Jeffrey C. Huston
Submissions from 1985
NASA LEWIS RESEARCH CENTER LOW-GRAVITY FLUID MANAGEMENT TECHNOLOGY PROGRAM., John C. Aydelott, Michael J. Carney, and John I. Hochstein
A photovoltaic cathodic protection system for an underground pipeline in Zimbabwe., G. Lewis
PHOTOVOLTAIC CATHODIC PROTECTION SYSTEM FOR AN UNDERGROUND PIPELINE IN ZIMBABWE., G. Lewis
CONSTANT-AMPLITUDE FATIGUE BEHAVIOR OF FIVE CARBON OR LOW-ALLOY CAST STEELS AT ROOM TEMPERATURE AND minus 45 degree C., R. I. Stephens, J. H. Chung, S. G. Lee, H. W. Lee, A. Fatemi, and C. Vacas-Oleas
VARIABLE-AMPLITUDE FATIGUE CRACK INITIATION AND GROWTH OF FIVE CARBON OR LOW-ALLOY CAST STEELS AT ROOM AND LOW CLIMATIC TEMPERATURES., R. I. Stephens, A. Fatemi, H. W. Lee, S. G. Lee, C. Vacas-Oleas, and C. M. Wang
Submissions from 1984
COMPUTATIONAL MODELING OF JET INDUCED MIXING OF CRYOGENIC PROPELLANTS IN LOW-G., J. I. Hochstein, P. M. Gerhart, and J. C. Aydelott
Some aspects of the production of ethanol from sugar cane residues in Zimbabwe, Gladius Lewis
The economics of domestic solar water heating, Gladius Lewis
Constant and variable amplitude fatigue behavior of five cast steels at room temperature and -45°C, R. I. Stephens, J. H. Chung, A. Fatemi, H. W. Lee, S. G. Lee, C. Vaca-Oleas, and C. M. Wang
Three-wheeled ATV a no-suspension rigid rider system, part ii: Applications handling and ride, Teong Eng Tan and Jeffrey C. Huston
Three-wheeled ATV-A no-suspension rigid rider system, part I: Modeling and parameter values, Teong Eng Tan and Jeffrey C. Huston
Submissions from 1983
Probabilistic estimation of extreme climatological parameters over Zimbabwe., G. Lewis
Diffuse irradiation over Zimbabwe, Gladius Lewis
Estimates of irradiance over Zimbabwe, Gladius Lewis
Submissions from 1982
The corrosion inhibition of copper by benzimidazole, G. Lewis
AUGER ANALYSIS OF BENZIMIDAZOLE-PASSIVATED COPPER., Gladius Lewis
Ellipsometric detection of the films formed on copper in an inhibitive solution, Gladius Lewis
QUANTUM CHEMICAL PARAMETERS AND CORROSION INHIBITION EFFICIENCY OF SOME ORGANIC COMPOUNDS., Gladius Lewis
Submissions from 1981
Electrochemical machining as a method of preparing grained aluminium surfaces, J. E. Bannard, J. R. Duncan, and G. Lewis
Adsorption isotherm for the copper-benzotriazole system, Gladius Lewis
CORROSION OF BRAZED-ON SHIELD OF STEAM TURBINE BLADES., Gladius Lewis
Irradiance estimates for Zambia, Gladius Lewis
USE OF AUGER ELECTRON SPECTROSCOPY AND ELLIPSOMETRY IN THE STUDY OF CORROSION INHIBITION., Gladius Lewis
Submissions from 1980
The corrosion of Fe12Cr iron-chromium alloys in o-Phosphoric acid, G. Lewis, P. G. Fox, and P. J. Boden
Submissions from 1979
Some chemical aspects of the corrosion inhibition of copper by benztriazole, P. G. Fox, G. Lewis, and P. J. Boden
An ellipsometric study of the films formed on an iron-chromium alloy in orthophosphoric acid, G. Lewis and M. J. Chappell
Natural Vegetable Fibres as Reinforcement in Cement Sheets, Gladius Lewis and Premalal Mirihagalia
A low-cost roofing material for developing countries, G. Lewis and P. Mirihagalia
Submissions from 1978
ADSORPTION OF BENZOTRIAZOLE ONTO CUPROUS OXIDE SURFACE - AN ELECTRODE IMPEDANCE STUDY., G. Lewis
The thickness of thin surface films determined by photo-electron spectroscopy, G. Lewis and P. G. Fox
